News:

It appears that the upgrade forces a login and many, many of you have forgotten your passwords and didn't set up any reminders. Contact me directly through helpmelogin@dodgecharger.com and I'll help sort it out.

Main Menu

Best Method to Slow/Stop Rust in a Pinch?

Started by Skull-1, January 10, 2019, 12:16:32 AM

Previous topic - Next topic

Skull-1

I am about to be sick...

My poor old Charger is gonna need all the trunk drip rails replaced (again) along with some quarter panel patches due to rust.    I guess the guys that restored this before didn't paint underneath after welding and I'm getting lots of rust erupting there.    (I'll post pics later.)

I don't have the money to fix it at the moment so other than running a dehumidifier in the garage is there anything I can do to slow it down?    It's already gone all the way through in some spots as evidenced by bubbles in the paint on the top side. 

This is really disappointing.   :(
http://www.dodgecharger.com/forum/index.php/topic,6231.0.html

1969 Dodge Charger "Ol' Yeller"
1991 Buick Regal Custom
1992 Buick Regal Custom
1995 Buick Regal Gran Sport
1996 Buick Regal SE (R.I.P.)

Ryan.C

There are few problems in life that cannot be solved with C-4.

b5blue

"OSPHO" saved my car for years. Highly acid based, watery it burns the rust black. If you keep applying and scrubbing you can get down to the metal. (I've used it for 25 years.) Reduce/halt raw rust and use Eastwood rust encapsulator to seal and you give years of delaying action. I see now they have an even better Platinum rust paint. I tested many paints like "Rust Bullet" by applying and later grinding off and really none can absorb into rust like ads may have you think. 

http://www.ospho.com

https://www.eastwood.com/eastwood-black-rust-encapsulator-paint-over-rust.html


Dano 1

I have similar issues to yours by the sounds of it, it'll be a while before I can fully restore/paint my car the 'right' way but in the meantime I don't want it getting worse.

I've heard great things about OSPHO per b5blue's comment, PrepnEtch is a similar product you can get at Home Depot which works the same way as it contains the same base chemical, phosphoric acid. Just be mindful of your future plans as both products can interact with certain primers/paints without being completely neutralized.
1969 Charger 383 2bbl, R4 red, White hat special project

Check out my website for 3D printed restoration parts and accessories.
www.nextgendesignsnc.com

Skull-1

Thanks, both of you.   I'll look into it.   
http://www.dodgecharger.com/forum/index.php/topic,6231.0.html

1969 Dodge Charger "Ol' Yeller"
1991 Buick Regal Custom
1992 Buick Regal Custom
1995 Buick Regal Gran Sport
1996 Buick Regal SE (R.I.P.)

Dano 1

Another option that I just thought about could be Fluid Film (https://www.fluid-film.com). It's a waxy coating usually used as an undercoat to protect against salt/water. It's non-permanent but great at stopping moisture and water intrusion.
1969 Charger 383 2bbl, R4 red, White hat special project

Check out my website for 3D printed restoration parts and accessories.
www.nextgendesignsnc.com

charger_fan_4ever

I think your problem was due to pin holes in the welds.moisture gets in there then all hell breaks loose.
Patching the quarters again will be a risk of it happening again. Consider the full quarters especially if you have rust aroind the sail panels and back window.
At this point you could use some chainsaw oil and add some wax to it and spray up inside the quarters. It has good penetration and a little wax thickens it up. Not best thing for a vehicle that runs in the salt,but thats not your case.

Dino

Spray it with ospho and let it be until you can fix it. It's good stuff and easily removed.
Extraordinary claims require extraordinary evidence.

Skull-1

Quote from: charger_fan_4ever on February 16, 2019, 07:28:10 PM
I think your problem was due to pin holes in the welds.moisture gets in there then all hell breaks loose.
Patching the quarters again will be a risk of it happening again. Consider the full quarters especially if you have rust aroind the sail panels and back window.
At this point you could use some chainsaw oil and add some wax to it and spray up inside the quarters. It has good penetration and a little wax thickens it up. Not best thing for a vehicle that runs in the salt,but thats not your case.

I have a set of full quarters, but the metal is cheap compared to my originals.   That's why we tried to save these.   :(

Very bummed...
http://www.dodgecharger.com/forum/index.php/topic,6231.0.html

1969 Dodge Charger "Ol' Yeller"
1991 Buick Regal Custom
1992 Buick Regal Custom
1995 Buick Regal Gran Sport
1996 Buick Regal SE (R.I.P.)

Skull-1

Quote from: Dino on February 17, 2019, 09:22:58 AM
Spray it with ospho and let it be until you can fix it. It's good stuff and easily removed.

Will do.  Thanks for backing b5blue on this one.  I'll try it.

Any vendors selling in smaller quantities than the link posted above?
http://www.dodgecharger.com/forum/index.php/topic,6231.0.html

1969 Dodge Charger "Ol' Yeller"
1991 Buick Regal Custom
1992 Buick Regal Custom
1995 Buick Regal Gran Sport
1996 Buick Regal SE (R.I.P.)

Dino

Quote from: Skull-1 on March 18, 2019, 01:36:05 PM
Quote from: Dino on February 17, 2019, 09:22:58 AM
Spray it with ospho and let it be until you can fix it. It's good stuff and easily removed.

Will do.  Thanks for backing b5blue on this one.  I'll try it.

Any vendors selling in smaller quantities than the link posted above?

Ace Hardware sells the quart bottles.
Extraordinary claims require extraordinary evidence.

b5blue

I just treated some light bleed through rust on the underside of my rockers with OSPHO, cleaned off a day later with a damp green scrubby and wiped dry. Top coated with Rust Encapsulator Platinum from Eastwood it's now sealed up nice.  :2thumbs:

charger_fan_4ever

Quote from: Skull-1 on March 18, 2019, 01:35:40 PM
Quote from: charger_fan_4ever on February 16, 2019, 07:28:10 PM
I think your problem was due to pin holes in the welds.moisture gets in there then all hell breaks loose.
Patching the quarters again will be a risk of it happening again. Consider the full quarters especially if you have rust aroind the sail panels and back window.
At this point you could use some chainsaw oil and add some wax to it and spray up inside the quarters. It has good penetration and a little wax thickens it up. Not best thing for a vehicle that runs in the salt,but thats not your case.

I have a set of full quarters, but the metal is cheap compared to my originals.   That's why we tried to save these.   :(

Very bummed...

AMD full 1/4's?

My 70 AMD 1/4s were actually thicker than the originals. Not by much though.

Skull-1

Quote from: Dino on March 18, 2019, 04:53:26 PM
Quote from: Skull-1 on March 18, 2019, 01:36:05 PM
Quote from: Dino on February 17, 2019, 09:22:58 AM
Spray it with ospho and let it be until you can fix it. It's good stuff and easily removed.

Will do.  Thanks for backing b5blue on this one.  I'll try it.

Any vendors selling in smaller quantities than the link posted above?

Ace Hardware sells the quart bottles.

Awesome.    Got some and have been using it on my Charger.....my truck....metal patio furniture.....    I even used it to bleach out an oil stain on the street.    Lol. 
http://www.dodgecharger.com/forum/index.php/topic,6231.0.html

1969 Dodge Charger "Ol' Yeller"
1991 Buick Regal Custom
1992 Buick Regal Custom
1995 Buick Regal Gran Sport
1996 Buick Regal SE (R.I.P.)