DodgeCharger.com Forum
August 15, 2022, 04:42:56 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Please remember: this is the place to discuss Chargers - NOT the place to discuss politics. Political posts will be locked or deleted at the Moderator's discretion.
 
   Home   Help Calendar Login Register Chat  
Pages: 1 2 3 [All]   Go Down
  Print  
Author Topic: Stainless Steel Trim Fasteners - '68 - '70 Charger  (Read 38714 times)
Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« on: January 30, 2007, 08:29:35 AM »

As I get closer to the point in my project where I need to install the vinyl top I realize there is a lot more to it than meets the eye.  I have learned that when the vinyl top is ready to go on, all of the stainless steel trim must go on shortly thereafter.  This includes all of the vinyl top trim as well as the windshield and backglass mouldings.

Recently, I have seen a couple of threads asking questions about the type of fasteners used to hold these reveal mouldings in place.  Since I still have questions as to which fasteners are correct, I have decided to do a bit of research and post my findings for everyone to use with the hope that anyone that can add to this, will surely do so.

Over the past few years I have taken photos of any type of fastener that I have seen on Chargers in salvage yards to ensure that when it comes time to install my stainless steel trim I do it with the proper hardware.

To get things started I have scanned a couple of pages from the 1969 Dodge Parts book. 

The first is an exterior sketch of the '69 Charger with reference numbers pointing to the trim available on the car that year.  The next page is a list showing the reference numbers with the corresponding part number for the trim as well as the part numbers for the appropriate fasteners.  Since I am focusing on the vinyl top and the associated trim, I have not spent any time looking at the other fasteners such as the medallions, grille trim etc.  That can always be added later.  Next, I made a list of the fastener part numbers and sorted them two ways:

1.) Sorted by Reference Number on the Sketch
2.) Sorted by the Fastener Part Number.

I then used some photos and added some text indicating the part number for the trim as well as the part number for the fastener. 

Now I realize that many of the part numbers for the fasteners are either no longer available from Mopar or may have been superseded and I also realize that there are numerous vendors out there selling trim fasteners such as these however, I have seen some of the items for sale and more often than not, I see incorrect items advertised.  I am not stating that I am some sort of expert on these but some of the items I have seen do no look familiar whatsoever.  Perhaps the reference photos I have taken are of cars that have had incorrect fasteners installed before they ended up in the salvage yard, hence this thread!

Here is where we could use your help.  If anyone has any photos of trim fasteners, whether it be ones you purchased or ones you have taken off of your car during your project, please feel free to post them here with a description of what trim they were holding in place.  That way we can figure out exactly what size trim fasteners are needed for each particular application.

I'll post what I have to get things started.


* bb_-_Exterior_Mouldings_-_Reference_Numbers.jpg (42.25 KB, 776x600 - viewed 8517 times.)

* bb_-_Exterior_Mouldings_-_Part_Number_List.jpg (93.08 KB, 600x776 - viewed 7774 times.)

* bb_-_Sorted_by_Reference__on_Sketch.jpg (74.44 KB, 640x387 - viewed 7843 times.)

* bb_-_Sorted_by_Part_.jpg (70.16 KB, 640x393 - viewed 7810 times.)
Logged
Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #1 on: January 30, 2007, 08:34:45 AM »

Windshield & Backglass Trim


* bb_-_Windshield_Trim.jpg (93.48 KB, 640x477 - viewed 7744 times.)

* bb_-_Windshield_Trim_2.jpg (88.81 KB, 640x480 - viewed 8120 times.)

* bb_-_Backglass_Trim.jpg (89.36 KB, 640x474 - viewed 8139 times.)

* bb_-_Backglass_Trim_2.jpg (84.59 KB, 640x475 - viewed 8099 times.)
Logged
Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #2 on: January 30, 2007, 08:45:03 AM »

Below is a photo of a Windshield Trim set.

There are two types of fasteners used to hold the windshield trim in place.

The larger fastener (# 6001 855) is used on the bottom windshield trim only.  Looks like fiver per side.

The smaller fastener (# 6002 263) is used to hold on all of the other pieces of trim.  This fastener is also used to hold the backglass trim in place.


* cc_-_Windshield_Trim.jpg (69.24 KB, 720x480 - viewed 7516 times.)
Logged
Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #3 on: January 30, 2007, 08:49:57 AM »

Now, as far as the door trim goes, this is where I might need some help as the manual shows six different fasteners holding that long stainless steel strip in place.

I have included a photo of one I saw on a '68 but I am unsure as to which part number it is.


* aa_-_Door_Trim.jpg (87.62 KB, 478x640 - viewed 7658 times.)

* DDDSC05156.JPG (148.3 KB, 640x480 - viewed 7554 times.)

* DDDSC05157.JPG (154.42 KB, 640x480 - viewed 7524 times.)

* DDDSC05159.JPG (150.14 KB, 640x480 - viewed 7565 times.)
Logged
Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #4 on: January 30, 2007, 08:55:42 AM »

The long stainless steel strip that runs along the sail panel, covering the bottom of the vinyl top has also got me asking a few questions.

Attached are a few photos I have of what I think is the proper fastener holding the end in place, but I am unsure of the other type of clips.


* aa_-_Vinyl_Top_Trim_2.jpg (70.23 KB, 640x480 - viewed 7417 times.)

* DDDSC05188.JPG (145.75 KB, 640x480 - viewed 7419 times.)

* DDDSC05189.JPG (149.36 KB, 640x480 - viewed 7430 times.)

* DDDSC05187.JPG (153.04 KB, 640x480 - viewed 7481 times.)
Logged
Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #5 on: January 30, 2007, 09:02:35 AM »

The trim under the quarter glass also uses a "J" nut, but I am unsure of what it looks like.  Attached is a photo of the screws.


* bb_-_Qtr_Glass_Lower_J-Shaped_Trim.jpg (84.42 KB, 640x478 - viewed 7713 times.)

* DSDDDSC05244.JPG (152.13 KB, 640x480 - viewed 7403 times.)

* DSDDDSC05246.JPG (153.82 KB, 640x480 - viewed 7402 times.)

* DSDDDSC05247.JPG (154.46 KB, 640x480 - viewed 7404 times.)
Logged
Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #6 on: January 30, 2007, 09:05:31 AM »

The checkmarks seem pretty straighforward - three nuts holding them in place.  Anyone have a photo of the nut with the seal?


* ff_-_Checkmark_Trim.jpg (80.49 KB, 640x473 - viewed 7536 times.)
Logged
Back N Black
Old Timer
*****
Offline Offline

Posts: 3,770



« Reply #7 on: January 30, 2007, 09:47:52 AM »

Wow! Shakey,
I'm impressed thats alot of good info you have there and good timing,i was at the body shop on friday and we were trying to figure out where the window clips fit on the back window.
Thanks again
Logged
Dennis K
Full Member
***
Offline Offline

Posts: 240


« Reply #8 on: January 30, 2007, 04:56:55 PM »

Here's what I have for the trim clips on the top of the door on my 68. There are 7 push-in style clips, with the 3 larger ones being the same and four others that get progressively smaller toward the front of the door, which would account for 5 different part numbers. None of the 68 doors that have seen have the rear trim clip with the nut on the bottom, so that might be something that was added later in 68 or 69, and would account for the 6th part number.


* doortrimclips.jpg (161.14 KB, 400x300 - viewed 7088 times.)
Logged
Dennis K
Full Member
***
Offline Offline

Posts: 240


« Reply #9 on: January 30, 2007, 05:08:35 PM »

Here's the nut on the check molding, maybe what they mean by "seal" is the white foam gasket around the stud or maybe that they packed the speed nut full of black butyl before they put it on the stud.


* checkmoldingnut100_0880.jpg (181.33 KB, 400x300 - viewed 7233 times.)
Logged
Dennis K
Full Member
***
Offline Offline

Posts: 240


« Reply #10 on: January 30, 2007, 05:14:25 PM »

and here's the j-nuts for the belt molding under the quarter windows.


* beltmoldingjnut.jpg (70.56 KB, 414x311 - viewed 7241 times.)
Logged
Dennis K
Full Member
***
Offline Offline

Posts: 240


« Reply #11 on: January 30, 2007, 05:21:25 PM »

And here's what I have for the long stainless steel vinyl top moldings. 3 of the push-in style at the front end of the molding and 2 of the stud/nut style in the rear on each side of the car. The one in the pic with the stud is a new aftermarket part.


* vtoptrimclip.jpg (184.54 KB, 400x300 - viewed 7005 times.)
Logged
Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #12 on: January 31, 2007, 07:22:53 AM »

Hey Dennis - thanks for your input and photos.  They will definitely help myself and others when trying to find the proper fasteners.

Case in point.

There is a seller on e-bay that has a bunch of fastener kits for sale and without knowing exactly what one is looking for, well this could lead to purchasing items that simply don't work.

Attached are two photos.

The first is a vinyl top trim kit, which looks correct to me other than the fact the seals are not included and there looks as though there may be one extra push in type clip.  No big deal.

However, the second photo shows the top of door and quarter trim kit, which doesn't look correct to me.

Any more input is appreciated folks.

Thanks in advance.


* e-bay_package_-_vinyl_top.jpg (70.04 KB, 640x433 - viewed 7274 times.)

* e-bay_package_-_top_of_door__quarter.jpg (62.53 KB, 592x400 - viewed 7135 times.)
Logged
Just 6T9 CHGR
Old Timer
*****
Offline Offline

Posts: 13,604


AKA... "The Game Changer"


« Reply #13 on: February 01, 2007, 11:31:27 AM »

Great write up Mike cheers

That lower kit for the door moldings doesnt look right.  The clips are definaltely like the ones Dennis posted....progressively smaller towards he front.

It is possiblle that the weird looking spring type clips can be made to work for the smaller part of the trim though....
Logged

Chris' '69 Charger R/T

Chatt69chgr
Old Timer
*****
Offline Offline

Posts: 2,064


« Reply #14 on: February 01, 2007, 08:48:59 PM »

I havn't taken my car apart so can't contribute but was thinking that if a vendor(s) could be identified that have the correct parts and/or kits, it would be nice to know who they are along with their catalog or item/part number.  That way, we could all immediately order the correct fasteners and along with printouts of this thread, have the parts and info we all need to restore our cars.  In fact, that is more or less what I have been doing for some time.  I follow the threads and when there is a concensus on something, I usually order that item right away and check it off my never ending list.   
Logged
Corellian Corvette
Senior Member
****
Offline Offline

Posts: 501


« Reply #15 on: March 04, 2007, 06:57:07 PM »

Shakey - did you every find someone on ebay who had the correct upper door stainless fastners? Going to be getting to this part of my car soon and would like to have the right kit!

Also, I did some searching online and found this place with a pretty good catalog (even has some chrysler number replacements)

http://www.hillcofasteners.com/

Right around page 135 here they have the types of clips show below. No sealer, but a bunch of different sizes. If you could measure the ones you have, you could probably match them up.

http://www.hillcofasteners.com/pdf/05_P81-P150.pdf

If you could give me the measurements I could check as well.

thanks again!
Logged
Ghoste
Old Timer
*****
Offline Offline

Posts: 41,092



« Reply #16 on: March 05, 2007, 04:28:41 AM »

Does anyone have a copy of that B-body fasteners book?  And how accurate is it?
Logged

Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #17 on: January 30, 2008, 05:17:59 PM »


Yo Bull!   wave
Logged
bull
Old Timer
*****
Offline Offline

Posts: 20,128


'68 383/2bbl/4spd 1 of 74


« Reply #18 on: January 30, 2008, 07:59:05 PM »


Yo Bull!   wave

Oh, hi! Fancy meeting you here. icon_smile_blackeye This thread is OCD central. yesnod And very helpful. Thanks!
Logged

Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #19 on: August 13, 2008, 07:13:03 PM »

Bump to the top for that other guy that was asking about chrome trim.
Logged
gasoline_24
Senior Member
****
Offline Offline

Posts: 592



« Reply #20 on: August 13, 2008, 08:26:56 PM »

I have the B-body fastener book, but did not see anything on these.  I will look again though.  Anyone find a nice kit for the top of door trim?  Has anyone found the foam pieces that are on the originals?  Were these the seals?  If not, what is everyone using to seal the fasteners?
Logged
Sweet T
Junior Member
**
Offline Offline

Posts: 147



« Reply #21 on: August 13, 2008, 10:42:00 PM »

Seal the fastners.....I just got the car back from getting the vinyl top on and for what they charged me they better of sealled them.
Logged

No, it ain't a Hemi.....thank God!
69*F5*SE
Old Timer
*****
Offline Offline

Posts: 1,850



« Reply #22 on: August 14, 2008, 09:54:39 AM »

 popcrn  Good stuff here.
Logged
bull
Old Timer
*****
Offline Offline

Posts: 20,128


'68 383/2bbl/4spd 1 of 74


« Reply #23 on: November 29, 2008, 04:43:14 AM »

Still nothing out there as far as repro J-nuts as far as I can tell. I got a couple used ones but I still email some of these fastener places asking about the possibility of them being reproduced. I'm waiting to hear back from one place as we speak.
Logged

Dodge Don
Old Timer
*****
Offline Offline

Posts: 2,255


70 Charger R/T SE 440 Six Pack Toronto Canada


WWW
« Reply #24 on: February 28, 2009, 06:15:23 AM »

Great thread Mike.

So exactly how many 6002263 clips were used for the rear window?

Any for the front windshield...how many 6002263 and how many 6001855 are needed?

I see the Totally Auto clip set for 68-70 Charger Front Windshield includes 2 short but wide clips that haven't been referenced in this thread...another Totally Auto goof up?
Logged

Dodge Don
Old Timer
*****
Offline Offline

Posts: 2,255


70 Charger R/T SE 440 Six Pack Toronto Canada


WWW
« Reply #25 on: February 28, 2009, 01:23:40 PM »

Anyone?
Logged

Dodge Don
Old Timer
*****
Offline Offline

Posts: 2,255


70 Charger R/T SE 440 Six Pack Toronto Canada


WWW
« Reply #26 on: March 27, 2009, 12:46:09 PM »

Great thread Mike.

So exactly how many 6002263 clips were used for the rear window?

Any for the front windshield...how many 6002263 and how many 6001855 are needed?

I see the Totally Auto clip set for 68-70 Charger Front Windshield includes 2 short but wide clips that haven't been referenced in this thread...another Totally Auto goof up?

Still looking for an answer on this.  brickwall
Logged

Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #27 on: March 29, 2009, 10:13:50 AM »

Great thread Mike.

So exactly how many 6002263 clips were used for the rear window?

Any for the front windshield...how many 6002263 and how many 6001855 are needed?

I see the Totally Auto clip set for 68-70 Charger Front Windshield includes 2 short but wide clips that haven't been referenced in this thread...another Totally Auto goof up?

Still looking for an answer on this.  brickwall

Hi Don,

Your answers to your first two questions are in the first post re: Excel screen shots.

Sorry I don't have an answer about the two oddball clips.
Logged
mopar_nut_440_6
Senior Member
****
Offline Offline

Posts: 883



WWW
« Reply #28 on: March 31, 2009, 04:18:35 PM »

Great info.

Thank you,
Logged

1968 Charger R/T 440 
2004 Dodge Ram 2500 680 HP Cummins with attitude
dodgey68
Full Member
***
Offline Offline

Posts: 453



« Reply #29 on: March 31, 2009, 05:11:25 PM »

and here's the j-nuts for the belt molding under the quarter windows.
Can any one help me out on were to get  j-nuts things as i have none
thank you
Logged

when all you own is a hammer, every job  resembles a nail.
Just 6T9 CHGR
Old Timer
*****
Offline Offline

Posts: 13,604


AKA... "The Game Changer"


« Reply #30 on: March 31, 2009, 06:05:40 PM »

and here's the j-nuts for the belt molding under the quarter windows.
Can any one help me out on were to get  j-nuts things as i have none
thank you

http://www.rtspecialties.net/
Logged

Chris' '69 Charger R/T

bull
Old Timer
*****
Offline Offline

Posts: 20,128


'68 383/2bbl/4spd 1 of 74


« Reply #31 on: April 10, 2009, 01:34:48 AM »

and here's the j-nuts for the belt molding under the quarter windows.
Can any one help me out on were to get  j-nuts things as i have none
thank you

http://www.rtspecialties.net/

Chris, did you actually see the j-nut on that site somewhere or are you just throwing it out as a possible source?
Logged

Just 6T9 CHGR
Old Timer
*****
Offline Offline

Posts: 13,604


AKA... "The Game Changer"


« Reply #32 on: April 10, 2009, 05:42:32 PM »

Didn't actually see it.....maybe call him up?
Logged

Chris' '69 Charger R/T

Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #33 on: June 02, 2015, 07:37:26 AM »


A bump from the archives as promised
Logged
Shakey
Old Timer
*****
Offline Offline

Posts: 6,014


1969 Dodge Charger R/T SE - 440 AUTO


« Reply #34 on: June 02, 2015, 07:42:38 AM »


Upper Door Trim clips


* IIIIIMMG_0498.JPG (103.84 KB, 800x600 - viewed 2368 times.)
Logged
cdr
Old Timer
*****
Offline Offline

Posts: 6,187


Katy,Tx


« Reply #35 on: June 02, 2015, 09:58:36 AM »

THanks Shakey !!! now if i can find them , i will keep looking.
Logged

LINK TO MY STORY http://www.onallcylinders.com/2015/11/16/ride-shares-charlie-keel-battles-cancer-ms-to-build-brilliant-1968-dodge-charger/  
                                                                                           
68 Charger 512 cid,9.7to1,Hilborn EFI,Home ported 440 source heads,small hyd roller cam,a518 trans,3.54 gear,11.04@123,4100lbs on street tires full exhaust daily driver
Charger55 by Charlie Keel, on Flickr
Eldovert
Junior Member
**
Offline Offline

Posts: 54


« Reply #36 on: December 02, 2015, 05:23:58 PM »

Does anyone have the measurements for these clips ?
Restoration Specialties can help me out but they want the dimensions
Thank you,Pat


* door top trim clips.JPG (147.38 KB, 640x480 - viewed 2489 times.)
Logged
keepat
Old Timer
*****
Offline Offline

Posts: 1,784



« Reply #37 on: December 04, 2015, 05:56:49 PM »


 All the spring clips are 3/4" wide
Red 7/8,  yellow 13/16, black 11/16,  Brown 5/8, green 9/16
I hope this helps
Pat


Logged
Eldovert
Junior Member
**
Offline Offline

Posts: 54


« Reply #38 on: December 05, 2015, 10:29:20 AM »

This is just what I need..great reference !
Thank you for taking the time to post!
Cheers,Pat
Logged
cincyboy
Junior Member
**
Offline Offline

Posts: 76



« Reply #39 on: December 17, 2015, 10:13:44 AM »

Sticky?  Bookmark....whatever its called.
Logged
68pplcharger
Senior Member
****
Offline Offline

Posts: 818



« Reply #40 on: February 13, 2016, 12:40:06 PM »

.
Logged
69bfan
Full Member
***
Offline Offline

Posts: 260


WWW
« Reply #41 on: February 14, 2016, 07:19:44 PM »

Keep in mind when replacing the front windshield reveal molding clips that the early 68 cars used a different style lower clip for the two pieces of trim attached to the cowl.  They are much taller and thus sit lower down into the recessed area.  I believe that the transition period would have been probably in the January '68 time frame.  This taller clip was used on the 66 and 67 B-Bodies.  Also, in 1970, the four clips that are on the A-pillar were changed to a shorter profile.  The profile that had been used up to that time will work as the difference is next to nothing.  Nobody to my knowledge has ever reproduced the smaller clip as it was only used for the one year period and only used in a small amount and the other clips would work without the expense of tooling up for an additional clip.  As for as anyone making a really correct clip kit for almost any of these applications, you will not find it out there.  What you do find is that they have found something that may or may not work.  You can possibly get them to work, but they will take some tweaking.  We buy up all of the obsolete clips as we find them.  Just because something looks close, does not mean that it will work.  Always check the swap meets for boxes of old clips as you never know what you may find.  And if all else fails, it may come down to modifying something that will work with some fabricating.
Logged

Restoration Parts and Materials
Weatherstripping is our specialty, but we stock a wide assortment of restoration needs.
www.restorationpartsandmaterials.com
Hemidog
Old Timer
*****
Offline Offline

Posts: 2,675


'68 Charger 451/727/8.75


« Reply #42 on: November 24, 2016, 09:06:09 AM »

Any updates on these door moulding clips? I broke several when i removed the moulding (rusty).... RTSpecialties only have B-Body except Charger, and I cannot find anyting on MegaParts.
Logged
john108
Senior Member
****
Offline Offline

Posts: 972


« Reply #43 on: November 24, 2016, 09:01:09 PM »

I bought a complete set of window clips for my 68 Charger. The lower windshield clips didn't match.  I had to get the windshield lower clips for a 1967 Charger.  My 68 was built Dec 67.
Logged
1batt4u
New Member
*
Offline Offline

Posts: 45


« Reply #44 on: January 08, 2017, 11:08:35 PM »

Hi all,

Really need help on this.

I just bought the rear taillight panel trim pieces, the trim piece that goes under trunk lid, and the 2 pieces that go curve down. My car did not have those pieces, I guess holes were covered when car was painted sometime ago.

-I need to know what screws are used on the trunk lid trim piece, so I can make holes and use correct screws.

-The 2 side pieces, I know they use No 8 screws, No 10 were to big, didn't fit through. Are black oxide screws used on those since that part of the trim is painted black? Each trim piece has a "tab", which I gotta make a hole on panel so it can go though. Question, once those tabs go through panel, some sort of clips are used to hold piece in?

For those who worked with those trim pieces, please get back to me, really need this help!


Thank you,
Billy
Logged
1batt4u
New Member
*
Offline Offline

Posts: 45


« Reply #45 on: January 09, 2017, 10:40:14 PM »

Here are pictures of the pieces.

Does anyone know, or can someone check on their cars for me?

Thank you!






Logged
70 sublime
Old Timer
*****
Offline Offline

Posts: 3,901


next project 1969 Charger 383 auto


« Reply #46 on: January 10, 2017, 04:56:56 AM »

The tab on the corner piece hook into the end of the long piece that goes across the back edge of trunk opening
Logged

current project 69 Charger Daytona clone F6 green
next project 70 Charger FJ5 green
BLK 68 R/T
Old Timer
*****
Offline Offline

Posts: 1,619


68 Charger R/T, 493 stroker engine, 727 auto.


« Reply #47 on: January 10, 2017, 09:43:34 AM »

The pointy stubs that stick off of the curved trim pieces have palnuts attached to them from inside the trunk, they cut their own threads on the first install, also called speed nuts. Any local parts house should have them.



The long stainless piece that goes across the trunk opening is held on with the same screws as the wheel opening moldings I believe.
Logged
1batt4u
New Member
*
Offline Offline

Posts: 45


« Reply #48 on: January 26, 2017, 12:18:20 PM »

Thank you! I just have to figure out making precise holes on the rear panel.


The pointy stubs that stick off of the curved trim pieces have palnuts attached to them from inside the trunk, they cut their own threads on the first install, also called speed nuts. Any local parts house should have them.



The long stainless piece that goes across the trunk opening is held on with the same screws as the wheel opening moldings I believe.
Logged
chargerkid01
Full Member
***
Offline Offline

Posts: 491



« Reply #49 on: April 03, 2017, 03:54:45 PM »

Where can I get these ASAP?Huh

 All the spring clips are 3/4" wide
Red 7/8,  yellow 13/16, black 11/16,  Brown 5/8, green 9/16
I hope this helps
Pat



Logged
BLK 68 R/T
Old Timer
*****
Offline Offline

Posts: 1,619


68 Charger R/T, 493 stroker engine, 727 auto.


« Reply #50 on: April 03, 2017, 04:11:57 PM »

Where can I get these ASAP?Huh

 All the spring clips are 3/4" wide
Red 7/8,  yellow 13/16, black 11/16,  Brown 5/8, green 9/16
I hope this helps
Pat




Try here:
http://www.restorationspecialties.com/
Logged
Shmity1
New Member
*
Offline Offline

Posts: 40


« Reply #51 on: July 07, 2017, 09:00:13 AM »


Upper Door Trim clips

Good place to find these?

Thanks
Logged
hemiron1
Junior Member
**
Offline Offline

Posts: 50


« Reply #52 on: August 30, 2017, 07:11:28 PM »

Where can I get these ASAP?Huh

 All the spring clips are 3/4" wide
Red 7/8,  yellow 13/16, black 11/16,  Brown 5/8, green 9/16
I hope this helps
Pat



Did anyone have any luck finding these clips?
Logged
green69rt
Old Timer
*****
Offline Offline

Posts: 3,628


Current status


« Reply #53 on: October 30, 2017, 10:30:54 AM »

Here are pictures of the pieces.

Does anyone know, or can someone check on their cars for me?

Thank you!





I'm late to the show on this but just wanted to add the screws for this trim.  Also fit the wheel well trim. From Rock Auto....
https://www.rockauto.com/en/moreinfo.php?pk=586350&jsn=1
Logged

mopar4don
Old Timer
*****
Offline Offline

Posts: 1,207


« Reply #54 on: January 15, 2018, 11:33:25 AM »


 All the spring clips are 3/4" wide
Red 7/8,  yellow 13/16, black 11/16,  Brown 5/8, green 9/16
I hope this helps
Pat





Did anyone find a supplier for these door trim clips?
Logged

kent
Full Member
***
Offline Offline

Posts: 460



« Reply #55 on: December 06, 2018, 11:30:59 AM »

Any luck on finding those two retainer clips that are held by those little nuts for the rear of the door trim? One per side. I have been scouring the net all morning. AMK come close but not close enough.  Might just have to make something up???
Logged

Kent
kent
Full Member
***
Offline Offline

Posts: 460



« Reply #56 on: December 09, 2018, 06:36:55 PM »

Took me abit, but I found some. See if they have any in stock.
Logged

Kent
hemiron1
Junior Member
**
Offline Offline

Posts: 50


« Reply #57 on: December 09, 2018, 06:41:28 PM »

I had no luck at all. I made a few but when I used them I put dimples in the stainless....  more work!
Logged
BLK 68 R/T
Old Timer
*****
Offline Offline

Posts: 1,619


68 Charger R/T, 493 stroker engine, 727 auto.


« Reply #58 on: April 06, 2019, 09:52:51 AM »

Posting a link to the long J nuts that hold the rear quarter stainless trim. Credit goes to ChargerRT69 for the link  2thumbs
B-BODY QTR PANEL BELT TRIM LONG J CLIP
SOLD AS A SET OF 8 CLIPS AND SCREWS
http://www.rtspecialties.net/proddetail.asp?prod=6026552
Discussion around the clips as well.
http://www.dodgecharger.com/forum/index.php/topic,132042.0.html
Logged
ChargerRT69
Junior Member
**
Offline Offline

Posts: 80


'69 Charger R/T


« Reply #59 on: December 30, 2019, 11:22:25 AM »

Thanks BLK 68 R/T!

Hope it helps someone out!

Posting a link to the long J nuts that hold the rear quarter stainless trim. Credit goes to ChargerRT69 for the link  2thumbs
B-BODY QTR PANEL BELT TRIM LONG J CLIP
SOLD AS A SET OF 8 CLIPS AND SCREWS
http://www.rtspecialties.net/proddetail.asp?prod=6026552
Discussion around the clips as well.
http://www.dodgecharger.com/forum/index.php/topic,132042.0.html
Logged
Pages: 1 2 3 [All]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.11 | SMF © 2006-2009, Simple Machines LLC Valid XHTML 1.0! Valid CSS!
Page created in 0.114 seconds with 17 queries.