News:

It appears that the upgrade forces a login and many, many of you have forgotten your passwords and didn't set up any reminders. Contact me directly through helpmelogin@dodgecharger.com and I'll help sort it out.

Main Menu

I spoke with the Edelbrock guys about there carbs vs Holley...

Started by Paul G, July 24, 2005, 04:42:45 PM

Previous topic - Next topic

Paul G

Edelbrock had a booth set up at the Van Senus show today. I spent a few minutes talking with the guys. They said an Edelbrock carb can make make up to 20 more horse than an equivalent Holley. Anyone know if that is true? They asked what problems I was having with the Holley. (It is a 750 double pumper on my mildly built 440).  I told them it was leaking fuel and had a hesitation. They recommended an Edelbrock AVS #1813, 800 CFM . It has an electric choke with dual feed capability and adjustable vacuum secondaries. It has a nicer finish than the Holley does as well. They also said that fuel pressure going to it should be around 4 to 6 PSI. More than that can cause problems. They said that the fuel we get in the big cities is emissions formulated and is less dense. The float doesn't sit as high in the less dense fuel. Lower fuel pressures wont bleed by the needle and seat causing problems. Anyone have any thoughts on this?

If I change the carb I will need a new feed line, pressure regulator since my Holley Red fuel pump puts out more pressure than they recommend, and carb linkage. I am using the factory lines from the tank to the carb right now. Should I up size them or switch to braided hoses or something? I think I am going to start saving up for the switch over to an Edelbrock. What do you guys think?
1972 Charger Topper Special, 360ci, 46RH OD trans, 8 3/4 sure grip with 3.91 gear, 14.93@92 mph.
1973 Charger Rallye, 4 speed, muscle rat. Whatever engine right now?

Mopars Unlimited of Arizona

http://www.moparsaz.com/#

Silver R/T

INSTEAD a Holley will outflow eddie in most cases, and Holleys are rated (at least speed demon) to flow more cfm than rated
http://www.cardomain.com/id/mitmaks

1968 silver/black/red striped R/T
My Charger is hybrid, it runs on gas and on tears of ricers
2001 Ram 2500 CTD
1993 Mazda MX-3 GS SE
1995 Ford Cobra SVT#2722

BigBlockSam

i like Edelbrock carbs. hassel free. my holleys always had problems with dumping. always needed to adjust something and carry a hammer with me. to bang the crap out of them.  Rene
I won't be wronged, I wont be Insulted and I wont be laid a hand on. I don't do these things to others, and I require the same from them.

  [IMG]http://i45.tinypic.com/347b5v5.jpg[/img

Brightyellow69rtse

mmm well ive used em both. if the car gets weathered at all that nice finish is gonna look like ass in no time. it gets tarnished easily (my camaro not the charger dont worry) yes the eddy or carter is more a bolt on and go thing but holley makes more power if your willing to play with it. my holley cost me like 450 or so i forget. i kept messing with it and now it feels like a fuel injected car no bullshit, no bogs or hesitations anywhere whe just goes. i got a 800 eddy sittin in the box damn near brand new but i prefer the holley..............Mike

Duey

Anybody running a pro-form 830 annular on a strong 440?  Ron, Neil... your gyus thoughts?

Cheers,
Duey
73 SE Brougham, F3 , 440, 850 Pro-form, 727 w TA 10", 4.10SG

BigBlockSam

feels good now, won't last you'll have to mess with it in the futher. holleys are better for the drags but for street go with the   Edelbrock. spray alittle wd40 on the carb the finish will last longer. Rene
I won't be wronged, I wont be Insulted and I wont be laid a hand on. I don't do these things to others, and I require the same from them.

  [IMG]http://i45.tinypic.com/347b5v5.jpg[/img

MoparYoungGun

I'm personally a Holley/Demon guy so I would say stick with your Holley. A lot of times your decision just comes down to personal preference.

Also, since Duey asked about the Pro-Form 830 annular, what are the advantages and disadvantages of a down leg booster carb compared to a annular booster carb and vice versa. Thanks guys!

Duey

Quote from: MoparYoungGun on July 24, 2005, 09:57:05 PM
I'm personally a Holley/Demon guy so I would say stick with your Holley. A lot of times your decision just
comes down to personal preference.

Also, since Duey asked about the Pro-Form 830 annular, what are the advantages and disadvantages of a down leg booster carb compared to a annular booster carb and vice versa. Thanks guys!

MYG, I was told that annular boosters are a bit better for cars with longer duration cams and where there is less vacuum at low engine RPMs.  It is supposed to make the  carb a bit more sensitive to whatever signal making its way to the carb.  I'm running a .509 on 108 centers and there is not as much signal at the carb as when I was running the stock cam.

Cheers,
Duey
73 SE Brougham, F3 , 440, 850 Pro-form, 727 w TA 10", 4.10SG

MoparYoungGun

Ok, thanks Duey for clearing that up for me. It's much appreciated.

Chryco Psycho

my experience has Always been the opposite in that  Holley will make more power everytime
I have run the Proform carbs , they are extrememly responsive , a very nice carb for a few less $$

Lostsheep

I have always had decent luck with Holleys. I like them more I guess cause I kinna know how to mess with them. Nothing real technical, but still some is better than none.
My 68 has an Edlebrock on it now and Chryco had to help me adjust that booger. :drive:

firefighter3931

Quote from: Duey on July 24, 2005, 09:53:15 PM
Anybody running a pro-form 830 annular on a strong 440?   Ron, Neil... your gyus thoughts?

Cheers,
Duey

Duey, i'm using the proform main body on mine but it has downleg boosters. Personally i like an annular booster carb, especially with a single plane intake manifold. The annular boosters will diminish the flow slightly due to the larger percentage of space they occupy in the venturi. Fuel atomization is better because of the 360* discharge from the booster.   ;) and they work very well though. If i was starting from scratch, it would be an annular carb for sure. I had a brand new 750dp on mine installed by the previous owner so i just upgraded the mainbody.....and everything underneath it !   :devil:

Ron
68 Charger R/T "Black Pig" Street/Strip bruiser, 70 Charger R/T 440-6bbl Cruiser. Firecore ignition  authorized dealer ; contact me with your needs

Ghoste

I like them both.   I have an Eddy on my car now because in the past whenever I've had a Holley, I seem to spend a lot of time tinkering with it.  The AFB clone is pretty limited in what you can change and for me personally, on a street car, that's all good.
However, look under the hoods at the dragstrip or on top of the engines in the magazine dyno shootouts and what do you see nearly every time?  A Holley.
Based on Ron and Neils advice I am going to be putting another Holley on the car soon, but I won't be getting rid of the Eddy just yet either.

Silver R/T

Ill get back to you when I get my speed demon installed
http://www.cardomain.com/id/mitmaks

1968 silver/black/red striped R/T
My Charger is hybrid, it runs on gas and on tears of ricers
2001 Ram 2500 CTD
1993 Mazda MX-3 GS SE
1995 Ford Cobra SVT#2722

firefighter3931

Quote from: Silver R/T on July 25, 2005, 07:44:31 PM
Ill get back to you when I get my speed demon installed

I hope you have better luck than i did. The last two speed demons i worked on were horrible to tune....couldn't get them to idle : way too rich. >:( And fouled plugs very quickly while contaminating the oil with fuel. The floats were set correct and the power valve was sized properly for the application. And yes, i checked the power valve and it wasn't blown.

Ron
68 Charger R/T "Black Pig" Street/Strip bruiser, 70 Charger R/T 440-6bbl Cruiser. Firecore ignition  authorized dealer ; contact me with your needs

1970440RT

I have 2 eddys on my 440's because at the time I knew very little about adjusting carbs.  As I learned, I'm at my limit with the eddys.  The non adjustability on the eddy vs the Holley has now become a shortfall where as before it was an advantage.  The Edelbrocks seem to be easier to tune and get running decent if you are a beginner.  As you advance, I think a Holley would be a step up. ( compareable flowing carbs of course )

Chryco Psycho

this is exactly why I use Holley carbs , the Eddys are very limiting in there tunability

andy74

i have a 750 edelbrock now,had a 750 holley but it was junk.i have used both and had good luck with both,the tuning is better on the holley,but it seems like youalways have to fool around with them,on a street car i am always going with the eldey,strip the holley,just my 2 cents

Paul G

You guys have got me thinking about keeping the Holley and learning how to tune it. I am capable of learning I think. LOL. So this is going to lead to more threads.
1972 Charger Topper Special, 360ci, 46RH OD trans, 8 3/4 sure grip with 3.91 gear, 14.93@92 mph.
1973 Charger Rallye, 4 speed, muscle rat. Whatever engine right now?

Mopars Unlimited of Arizona

http://www.moparsaz.com/#

Moparstud440

IMHO Holley's rev a lot quicker then a eldenbrock.  Holley's also are better performing.  We had a 750 double pumper on our belvedere and it was running 8.10s n the 1/8th, but after having problems with it acting up and such we put an old eldenbrock on it and it runs 8.60's now.  Eldenbrock are def the way to go if you don't know anything about carburetors and just want to put it on and go.  Holley's make more power and are funner to drive IMHO, but are an absolute pain to get tuned right.  Last year my duster was an absolute perfect girl, one crank and she fired up and she would idle as soon as she started, no matter how cold she was.  Then we put a new bigger badder motor in and developed a stumble right at the hit of the throttle, we went up and down in jet and squirter sizes and everything.  Well 99% of the stumble is gone and shes running consist now, but you have to let her run for a good 10 mins before she'll idle on her own anymore.  But then I not an idling kinda guy, I like to the floor board.

Duey

Ron, Neil...looks like I goofed slightly, the 830 annulars I was looking at was actually a Holley 4150 HP, not the pro-form (850, downleg).  I'll be doing some extra work in the near future and was thinking that the 4150 HP 830 annular is probably worth the extra 125-150 bucks over the Pro-form...although both of those carbs are pretty nice, I figure.  I was looking into a Mighty Demon earlier, but I think I'll stick with the Holley (to mate up with my lovely sounding, old-school classic .509...  :icon_smile_big:

Cheers
Duey
73 SE Brougham, F3 , 440, 850 Pro-form, 727 w TA 10", 4.10SG

firefighter3931

The 830 annular is what i'd be buying if i was building your combo. The low end response will be better than with a downleg booster...no question. I didn't realize proform was making an annular booster carb....i've just looked at their main bodies. When i do the 493 you can be your last doller that ther'll be an annular booster carb on it. I'm liking the 4150 style hp1050 annular for that combo !   :devil:

Ron
68 Charger R/T "Black Pig" Street/Strip bruiser, 70 Charger R/T 440-6bbl Cruiser. Firecore ignition  authorized dealer ; contact me with your needs

bull

Quote from: firefighter3931 on July 25, 2005, 08:29:38 PM
Quote from: Silver R/T on July 25, 2005, 07:44:31 PM
Ill get back to you when I get my speed demon installed

I hope you have better luck than i did. The last two speed demons i worked on were horrible to tune....couldn't get them to idle : way too rich. >:( And fouled plugs very quickly while contaminating the oil with fuel. The floats were set correct and the power valve was sized properly for the application. And yes, i checked the power valve and it wasn't blown.

Ron

That sux. I was going to go with Demon but now I'm not sure anymore. Did you get part of a bad batch or something?

Chryco Psycho

Whil;e Demons have some nice features I still like Holley better , often you nned to change air bleeds to get the Demons right

Duey

Quote from: firefighter3931 on July 27, 2005, 09:24:42 PM
The 830 annular is what i'd be buying if i was building your combo. The low end response will be better than with a downleg booster...no question. I didn't realize proform was making an annular booster carb....i've just looked at their main bodies. When i do the 493 you can be your last doller that ther'll be an annular booster carb on it. I'm liking the 4150 style hp1050 annular for that combo !   :devil:

Ron

Roger that Ron, as you know, I won't be able to work on the car now until next spring...but I figure I'll get the 4150 HP 830 annular and take the time to tune it when I whack the engine on Shawn's dyno.  :icon_smile_big:

Duey
73 SE Brougham, F3 , 440, 850 Pro-form, 727 w TA 10", 4.10SG