News:

It appears that the upgrade forces a login and many, many of you have forgotten your passwords and didn't set up any reminders. Contact me directly through helpmelogin@dodgecharger.com and I'll help sort it out.

Main Menu

Amp Gauge problem

Started by Highbanked Hauler, December 01, 2009, 07:24:17 PM

Previous topic - Next topic

Highbanked Hauler

 I put in a low mileage amp gauge with the two wires in place and it doesn't work. I put the original back in which did work and now doesn't. Is there any way to test it?? :shruggy:
69 Charger 500, original owner  
68 Charger former parts car in process of rebuilding
92 Cummins Turbo Diesel
04 PT Cruiser

Nacho-RT74

amm gauge is a very simple gauge... a copper plate what mooves magnetically over a shunt linking both studs. The mooving plate does have a pivot and the needle attached. Just that.

is easy to check if pieces are in place. As far pieces are in place and free movement, gauge must work
Venezuelan RT 74 400 4bbl, 727, 8.75 3.23 open. Now stroked with 440 crank and 3.55 SG. Here is the History and how is actually: http://www.dodgecharger.com/forum/index.php/topic,7603.0/all.html
http://www.dodgecharger.com/forum/index.php/topic,25060.0.html

Highbanked Hauler

 Thanks, it must be a power or a ground problem then as the gauge looks new.
69 Charger 500, original owner  
68 Charger former parts car in process of rebuilding
92 Cummins Turbo Diesel
04 PT Cruiser

Nacho-RT74

not at gauge, ammeter doesn't get or need ground, is totally isolated from cluster.

if needle is not moving, no matter if D or C reading and ammeter is GOOD, power is not getting up to ammeter...

but ign key and main splice is AFTER ammeter, so must get D reading if some light or acc is on.

UNLESS you have an splice from alt to batt or related wires. That will bypass the ammeter
Venezuelan RT 74 400 4bbl, 727, 8.75 3.23 open. Now stroked with 440 crank and 3.55 SG. Here is the History and how is actually: http://www.dodgecharger.com/forum/index.php/topic,7603.0/all.html
http://www.dodgecharger.com/forum/index.php/topic,25060.0.html

Ghoste

The fact that your old one used to work but didn't after swapping it back in would tend to make me think it wasn't an issue with the guage.

scatpakrt

Locate the large black wire at your bulkhead connector and check for burned terminals there. Although it is a black wire it supplies the output of the alternator to supply power to everything. There is, on my 71 B body, a factory welded/soldered splice under the dash from the bulkhead on the inside of the car, and then it goes to the amp meter black terminal. Other side of amp meter has a red wire to starter relay "Batt" terminal. Check, with car running, for 12v + on both terminals of amp meter. Use a good ground with black portable meter lead and red lead to both amp meter terminals one at a time and see if 12v + is there. You should see 12v on the red wire to the starter relay present with just the key on, but the black will require the alt. to be running to output 12v.

Hope this helps your troubleshooting.

P.S. No ground involved on amp meter circuit so don't go chasing bad grounds for ampmeter problems. :cheers:
71 "Mr. Norm's" Charger R/T, 440 auto, 323 Suregrip, Bright Red
09 Challenger SRT8, 6.1 Hemi, auto, Brilliant Black Pearlcoat
08 Mega Cab, 2500 Diesel, auto, Brilliant Black Pearlcoat